Input devices

Table of content

Ultrasonic sensor HC-SR04

Thermistor

Moisture level sensor

Sensing plants activity

Let's play with sensors.


Part of this assignment is also covered on my final project's page.

The Green Observatory: Input

Created 25/03/2020

Updated 02/11/2020

Ultrasonic sensor HC-SR04

The ultrasonic sensor HC-SR04 provides 2Cm to 400cm of non-contact measurement functionality with a ranging accuracy that can reach up to 3mm. Here is its datasheet. This sensor has 4 pins that we have to connect to our dev board.

  • 5V supply
  • Trigger Pulse Input
  • Echo Pulse Output
  • GND
uno-ultrasonic-inuse
uno-ultrasonic-inuse

I'm using an Arduino UNO to use this sensor because it needs a voltage of 5V. Unfortunately, the Barduino and its ESP32 only has a voltage of 3.3V.

Connection

The connection is quite simple, the VCC goes to the 5V, the GND to the GND, the Echo to a digital pin, let's say the 12 and the Trig to another digital pin, the 11.

uno-ultrasonci-schematic
uno-ultrasonci-schematic

(image source)

Code

Here is the basic code to read data from the ultrasonic sensor, to convert them into readable values (cm) and print it on the serial monitor.

To quickly create a PlatformIO project for the Arduino UNO, open a terminal and navigate to a freshly created folder and type $ pio project init --board uno. As simple as that.

Create in new main.cpp file into the src folder.

int trigPin = 11;
int echoPin = 12;
long duration, cm;

void setup() {
  Serial.begin(9600);
  pinMode(trigPin, OUTPUT);
  pinMode(echoPin, INPUT);
}

void loop() {
  digitalWrite(trigPin, LOW);
  delayMicroseconds(5);
  digitalWrite(trigPin, HIGH);
  delayMicroseconds(10);
  digitalWrite(trigPin, LOW);
  pinMode(echoPin, INPUT);
  duration = pulseIn(echoPin, HIGH);
  cm = (duration/2) / 29.1;
  Serial.print(cm);
  Serial.print("cm");
  delay(250);
}

Compile it and upload it to the UNO pio run -t upload and open the serial monitor pio device monitor to see the distance value calculated by the ultrasonic sensor. I'm impressed how fast and accurate it is.

Explanations

cm = (duration/2) / 29.1 is how we convert the duration to a distance, using a formula: distance = (traveltime/2) * speed of sound. The speed of sound is 343m/s wich is equal to 1/29.1 cm/uS. We need to divide the traveltime by 2 because the wave we sent hit the object and then returned back to the sensor.

Created 26/03/2020

Updated 26/03/2020

Thermistor

Or how to measure temperature using a resistor.

To measure the temperature, we need to measure the resistance. However, a microcontroller does not have a resistance-meter built in. Instead, it only has a voltage reader known as a analog-digital-converter. So what we have to do is convert the resistance into a voltage, and we will do that by adding another resistor and connecting them in series. Now you just measure the voltage in the middle, as the resistance changes, the voltage changes too, according to the simple voltage-divider equation. We just need to keep one resistor fixed

Analog Voltage Reading Method, Adafruit

thermo-photo-1
thermo-photo-1
thermo-photo-2
thermo-photo-2

Connection

The thermistor is linked to the GND, and to the analog pin 0 and to the 5V pin through a 10 resistor.

(image source)

Code

Here is the piece of code that print the value of the analog pin 0 and convert its values into a Celcius temperature value.

#include <Arduino.h>
#include <math.h>

void setup()
{
  Serial.begin(9600);
}

// Function that applies the Steinhart-Hart equation
float thermistor(int val)
{
  float temp;
  // From raw analog values
  temp = log(((10240000 / val) - 10000));
  // To Kelvin values
  temp = 1 / (0.001129148 + (0.000234125 + (0.0000000876741 * temp * temp)) * temp);
  // Convert Kelvin to Celsius
  temp = temp - 273.15;
  return temp;
}

void loop()
{
  int val;
  float temp;
  val = analogRead(0);
  temp = thermistor(val);
  Serial.print(temp);
  Serial.println(" °C");
  delay(1000);
}

Main resource: this tutorial

Created 27/03/2020

Updated 09/01/2021

Moisture level sensor

Water is a conductive element, and the more water there is in the soil the more electricity can flow through it. So, in order to measure the soil moisture level, we can integrate it into an electrical circuit and measure the voltage. The more voltage in the circuit, the more water there is in the soil.

moist-setup
moist-setup

To represent it, I built a small system that lights a green LED when the soil is wet and a red LED when it's dry.

Connection

  • 5V from the Arduino UNO to the soil
  • A0 (anaolog) from the Arduino UNO to the soil
  • A0 (analog) from the Arduino UNO to the GND (analog) through a 10kΩ resistor
  • 11 (digital) to the red LED through a 220Ω resistor
  • 12 (digital) to the green LED through a 220Ω resistor
  • LED's to the GND (digital)
moist-closeup
moist-closeup

Code

The code is basic. If the analog pin gets a high voltage, it means that the soil is moist and the plant is happy so we turn on the green LED, and vice versa.

I plan to write a more complex code in the coming weeks, a code that takes into account the amount of water needed for each specific plant, and to alert when it's too dry or too weet.

int ledGreen = 12;
int ledRed = 11;
int contactVal = 0;

void setup() {
  Serial.begin(9600);
  pinMode(ledGreen, OUTPUT);
  pinMode(ledRed, OUTPUT);
}

void loop() {
  contactVal = analogRead(0);
  Serial.println(contactVal);
  if (contactVal >= 350) {
    digitalWrite(ledRed, LOW);
    digitalWrite(ledGreen, HIGH);
  } else {
    digitalWrite(ledRed, HIGH);
    digitalWrite(ledGreen, LOW);
  }
  delay(250);
}

Here is my tiny system in action, olé.

Created 28/03/2020

Updated 28/03/2020

Sensing plants activity

In the frame of my Fab Academy final project, I'm exploring how to sense the electrical activity of plants.

Listen to what we can observe from this lovely plant
Listen to what we can observe from this lovely plant

I covered this topic on a different article.

Sensing plants activity

Created 15/09/2020

Updated 15/09/2020