Work in progress:

Computer-Controlled Machining



on this week's assignment we had to make two pieces of furniture that we can use in the Lab using milling cut without glues or fasteners, the piece must be stable by design.

This weekly assignment has been made half to half with Daniel García, instead of making a piece of furniture each, we made two between the two.

The material we use to make the furniture is wooden planks of MDF 16 mm thick.

Machining has been made with a medium format CNC milling Alarsis FH250M, cutting dimensions 2,44 x1, 22 meters. We have used a 6mm diameter End Mill.
Examples

Testing fixture: stool


First try, testing joints. Before making the final furniture, we test the fixture making a stool, made by two pieces in X and a top board for sitting.

The fixture consists of adjusting joints to prevent movement of the parts and provide stability. The tolerance given to the joints was 0, so the assembly is more difficult but the parts remain fixed without using binder or screws. The result of the test is a stool which is stable even when you stand on it.
Examples Examples

First Furniture piece: worktable


This first piece of furniture is a worktable for using in the fabLAB where the top board is supported and serves as an anchor on six legs formed by four pieces that intersect each other to provide structural stability to the table. The board achieve to stiffen the assembly and give horizontal stability.

The first step was to make the design of the parts in CAD, for it we made the development of parts using AutoCAD 2D and then we did a first test using Rhinoceros 3D where we discovered some mistakes we solve.
Examples

With the corrected parts, we draw the templates for cutting. We had to use 3 planks of MDF 16mm thick to give greater strength.

The problem of milling parts is you must take into account the radius of milling in the corners, and never will be at 90 degrees. To fix that what we do is give a semicircle attached to the corner and so we make sure that the bond between the two pieas going to be perfect.
Examples

The software used by the CNC Machine is the Aspire. In the example images given, the pattern match to the second piece of furniture, but the cutting parameters are the same except for the thickness of the material, instead of 10 mm is 16 and and the number of passes is 3 instead of two.

The first thing we do at Aspire is to define the dimensions of the material (2.44x1.22 meters) and thickness of 16 mm. Import pattern cut from CAD in .dxf format and now we choose how to cut each line, selecting, indicating the depth of cut, if cut outside, inside or over the line and add tabs to hold the parts while cut and prevent movement and mill break.
Examples Examples

We select the tool that we will make the cut. In our case it is a Mill End 6 mm in diameter. It is important to select the right tool because in our design the corners have been done with a tool 6mm thick. The Mill expels chips compressing down and preventing cut pieces move.

The speeds chosen were 1500 to advance with a depth of 5.4 mm to make the cuts in three passes.
Examples Examples Examples Examples

Open the G-code into the machine controller. We use the Mach 3. In this controller we calibrate the 0,0,0 point in the material and we are ready to start milling.

After milling we make the first assembly and discover a design mistake, the junctions are so narrow that avoid some of then turn to get the right position. When assembly we did too much force and break a piece. The solution was easy because of changing the direction of one union is easily mounted without problems.

Also assemble the top board and we have the finished piece.
Examples Examples

Second Furniture piece: computer desk


Now let's do the second piece of furniture consisting of a desk to place the two computers for public use we have in the FabLab. The assembly system is very similar to the previous table, but the board used is 10 mm excluding the top board and the two beams that are 16 mm thick for added structural stability.

We design in AutoCAD 2D and 3D simulation assembly in Rhinoceros and when we see that the piece works we distribute the pieces on the template.
Examples Examples

We perform machining of parts with the Aspire software and cutting with the Mach 3 as we have seen with the previous model.