'----------------------------------------------------------------
'SHOPBOT ROUTER FILE IN MM
'GENERATED BY PARTWorks
'Minimum extent in X = 0.000 Minimum extent in Y = 0.000 Minimum extent in Z = -17.400
'Maximum extent in X = 2440.000 Maximum extent in Y = 1220.000 Maximum extent in Z = 0.000
'Length of material in X = 2440.000
'Length of material in Y = 1220.000
'Depth of material in Z = 17.400
'Home Position Information = Bottom Left Corner, Material Surface 
'Home X = 0.000000 Home Y = 0.000000 Home Z = 50.000000
'Rapid clearance gap or Safe Z = 50.000
'UNITS:MM
'
IF %(25)=0 THEN GOTO UNIT_ERROR	'check to see software is set to standard
SA                             	'Set program to absolute coordinate mode
CN, 90
'New Path
'Toolpath Name = KZ Pocket 1
'Tool Name   = End Mill (6 mm)

&PWSafeZ = 50.000
&PWZorigin = Material Surface
&PWMaterial = 17.400
'&ToolName = "End Mill (6 mm)"
&Tool =2           'Tool number to change to
C9                   'Change tool
TR,13500               'Set spindle RPM
C6                   'Spindle on
PAUSE 2
'
MS,45.5,22.8
JZ,50.000000
J2,0.000000,0.000000
J3,1300.298462,1060.825684,50.000000
J3,1300.298462,1060.825684,5.000000
M3,1300.298462,1060.825684,0.000000
M3,1304.957275,1043.438965,-1.666667
M3,1300.298462,1060.825684,-3.333333
M3,1340.803711,909.658325,-3.333333
M3,1344.667358,910.693604,-3.333333
M3,1304.162231,1061.860962,-3.333333
M3,1300.298462,1060.825684,-3.333333
J3,1300.298462,1060.825684,50.000000
J3,1300.298462,1060.825684,5.000000
M3,1300.298462,1060.825684,-3.333333
M3,1304.957275,1043.438965,-5.000000
M3,1300.298462,1060.825684,-6.666667
M3,1340.803711,909.658325,-6.666667
M3,1344.667358,910.693604,-6.666667
M3,1304.162231,1061.860962,-6.666667
M3,1300.298462,1060.825684,-6.666667
J3,1300.298462,1060.825684,50.000000
J3,1300.298462,1060.825684,5.000000
M3,1300.298462,1060.825684,-6.666667
M3,1304.957275,1043.438965,-8.333334
M3,1300.298462,1060.825684,-10.000000
M3,1340.803711,909.658325,-10.000000
M3,1344.667358,910.693604,-10.000000
M3,1304.162231,1061.860962,-10.000000
M3,1300.298462,1060.825684,-10.000000
J3,1300.298462,1060.825684,50.000000
JZ,50.000000
J2,0.000000,0.000000
'
'Turning router OFF
C7
END
'
'
UNIT_ERROR:
CN, 91                            'Run file explaining unit error
END