<b>https://eagle.componentsearchengine.com</b><p><author>Created by SamacSys</author>
<b>SOT23/SUPERSOT23, 3 LEAD, 1.4x2.9</b><br>
>NAME
>VALUE
<b>(SO)20-Lead(SOIC)</b><br>
>NAME
>VALUE
<b>LBR-127HLD_1</b><br>
>NAME
>VALUE
>NAME
>VALUE
>NAME
>VALUE
>NAME
>VALUE
<b>MOSFET SOT-23 N-CH LOGIC</b><p>
Source: <a href="https://www.mouser.de/datasheet/2/308/NDS355AN-D-1813055.pdf"> Datasheet </a>
<b>MICROCHIP - ATTINY3216-SN - 8 Bit MCU, AVR Family ATtiny3216 Series Microcontrollers, 20 MHz, 32 KB, 2 KB, 20 Pins, SOIC</b><p>
Source: <a href="http://www.microchip.com/mymicrochip/filehandler.aspx?ddocname=en606269"> Datasheet </a>
<b>Reflective Object Sensor</b><p>
Source: <a href="http://akizukidenshi.com/download/lbr127hld.pdf"> Datasheet </a>
<b>CAPACITOR</b>
>NAME
>VALUE
>NAME
>VALUE
<b>CAPACITOR</b>
>NAME
>VALUE
>NAME
LED 1206 pads (standard pattern)
>NAME
>VALUE
LED1206 FAB style (smaller pads to allow trace between)
>NAME
>VALUE
5mm round through hole part.
>NAME
>VALUE
<b>RESISTOR</b>
>NAME
>VALUE
<b>RESISTOR</b><p>
wave soldering
>NAME
>VALUE
>NAME
>VALUE
>Value
>Name
>Name
>Value
>Name
>Value
non-polarized capacitor
>NAME
>VALUE
(Black)
(Green)
LED
>NAME
>VALUE
>NAME
>VALUE
USB
>Name
>Value
LED
<b>Resistor (US Symbol)</b>
<p>
Variants with postfix FAB are widened to allow the routing of internal traces
SMD micro USB connector as found in the fablab inventory.
Three footprint variants included:
<ol>
<li> original, as described by manufacturer's datasheet
<li> for milling with the 1/100" bit
<li> for milling with the 1/64" bit
</ol>
<p>Made by Zaerc.
<b>Pin Header Connectors</b><p>
<author>Created by librarian@cadsoft.de</author>
<b>PIN HEADER</b>
>NAME
>VALUE
<b>PIN HEADER</b>
>NAME
>VALUE
PIN HEADER
PIN HEADER
>NAME
>VALUE
<b>PIN HEADER</b>
<b>Supply Symbols</b><p>
GND, VCC, 0V, +5V, -5V, etc.<p>
Please keep in mind, that these devices are necessary for the
automatic wiring of the supply signals.<p>
The pin name defined in the symbol is identical to the net which is to be wired automatically.<p>
In this library the device names are the same as the pin names of the symbols, therefore the correct signal names appear next to the supply symbols in the schematic.<p>
<author>Created by librarian@cadsoft.de</author>
>VALUE
<b>SUPPLY SYMBOL</b>
Since Version 8.2, EAGLE supports online libraries. The ids
of those online libraries will not be understood (or retained)
with this version.
Since Version 8.3, EAGLE supports URNs for individual library
assets (packages, symbols, and devices). The URNs of those assets
will not be understood (or retained) with this version.
Since Version 8.3, EAGLE supports the association of 3D packages
with devices in libraries, schematics, and board files. Those 3D
packages will not be understood (or retained) with this version.