'----------------------------------------------------------------
'SHOPBOT ROUTER FILE IN INCHES
'GENERATED BY PARTWorks
'Minimum extent in X = 0.000 Minimum extent in Y = 0.000 Minimum extent in Z = -0.650
'Maximum extent in X = 96.000 Maximum extent in Y = 48.000 Maximum extent in Z = 0.000
'Length of material in X = 96.000
'Length of material in Y = 48.000
'Depth of material in Z = 0.650
'Home Position Information = Bottom Left Corner, Material Surface 
'Home X = 0.000000 Home Y = 0.000000 Home Z = 0.800000
'Rapid clearance gap or Safe Z = 0.200
'UNITS:Inches
'
IF %(25)=1 THEN GOTO UNIT_ERROR	'check to see software is set to standard
SA                             	'Set program to absolute coordinate mode
CN, 90
'New Path
'Toolpath Name = ScrapProfileCut
'Tool Name   = 1/4"  Down-cut (57-910)

&PWSafeZ = 0.200
&PWZorigin = Material Surface
&PWMaterial = 0.650
'&ToolName = "1/4"  Down-cut (57-910)"
&Tool =3           'Tool number to change to
C9                   'Change tool
TR,12000               'Set spindle RPM
C6                   'Spindle on
PAUSE 2
'
MS,3.0,1.0
JZ,0.800000
J3,83.136497,22.372484,0.200000
M3,83.136497,22.372484,-0.140000
M3,33.734627,22.372484,-0.140000
M3,33.734627,-0.084310,-0.140000
J3,33.734627,-0.084310,0.200000
J3,83.136497,22.372484,0.200000
M3,83.136497,22.372484,-0.280000
M3,33.734627,22.372484,-0.280000
M3,33.734627,-0.084310,-0.280000
J3,33.734627,-0.084310,0.200000
J3,83.136497,22.372484,0.200000
M3,83.136497,22.372484,-0.420000
M3,33.734627,22.372484,-0.420000
M3,33.734627,-0.084310,-0.420000
J3,33.734627,-0.084310,0.200000
J3,83.136497,22.372484,0.200000
M3,83.136497,22.372484,-0.560000
M3,33.734627,22.372484,-0.560000
M3,33.734627,-0.084310,-0.560000
J3,33.734627,-0.084310,0.200000
J3,83.136497,22.372484,0.200000
M3,83.136497,22.372484,-0.700000
M3,33.734627,22.372484,-0.700000
M3,33.734627,-0.084310,-0.700000
J3,33.734627,-0.084310,0.200000
J3,83.136497,47.915691,0.200000
M3,83.136497,47.915691,-0.140000
M3,83.136497,-0.084310,-0.140000
J3,83.136497,-0.084310,0.200000
J3,83.136497,47.915691,0.200000
M3,83.136497,47.915691,-0.280000
M3,83.136497,-0.084310,-0.280000
J3,83.136497,-0.084310,0.200000
J3,83.136497,47.915691,0.200000
M3,83.136497,47.915691,-0.420000
M3,83.136497,-0.084310,-0.420000
J3,83.136497,-0.084310,0.200000
J3,83.136497,47.915691,0.200000
M3,83.136497,47.915691,-0.560000
M3,83.136497,-0.084310,-0.560000
J3,83.136497,-0.084310,0.200000
J3,83.136497,47.915691,0.200000
M3,83.136497,47.915691,-0.700000
M3,83.136497,-0.084310,-0.700000
J3,83.136497,-0.084310,0.200000
JZ,0.800000
J3,0.000000,0.000000,0.800000
'
'Turning router OFF
C7
END
'
'
UNIT_ERROR:
CN, 91                            'Run file explaining unit error
END