/*
  Software serial multple serial test

 Receives from the hardware serial, sends to software serial.
 Receives from software serial, sends to hardware serial.

 The circuit:
 * RX is digital pin 10 (connect to TX of other device)
 * TX is digital pin 11 (connect to RX of other device)

 Note:
 Not all pins on the Mega and Mega 2560 support change interrupts,
 so only the following can be used for RX:
 10, 11, 12, 13, 50, 51, 52, 53, 62, 63, 64, 65, 66, 67, 68, 69

 Not all pins on the Leonardo and Micro support change interrupts,
 so only the following can be used for RX:
 8, 9, 10, 11, 14 (MISO), 15 (SCK), 16 (MOSI).

 created back in the mists of time
 modified 25 May 2012
 by Tom Igoe
 based on Mikal Hart's example

 This example code is in the public domain.

 */

// constants won't change. They're used here to set pin numbers:
const int buttonPin = 3;     // the number of the pushbutton pin
const int ledPin =  7;      // the number of the LED pin

// variables will change:
int buttonState;         // variable for reading the pushbutton status
int previous = LOW;
int stateLED = LOW;
long time = 0;
long debounce = 200;

// resources:
#include <SoftwareSerial.h>     //load serial library
  SoftwareSerial mySerial(0, 1); // Serial definition: name(pins)(RX, TX)
//  int buttonState;


void setup() {
  pinMode(ledPin, OUTPUT);    // initialize the LED pin as an output:
  pinMode(buttonPin, INPUT);  // initialize the pushbutton pin as an input:
//  pinMode(3, INPUT);
  mySerial.begin(115200);    //serial.start(baudios velocity)
//   digitalWrite(ledPin, HIGH);    // turn LED off
  
}

void loop() { 

//  buttonState = digitalRead(3);
  buttonState = digitalRead(buttonPin);  // read the state of the pushbutton value:

//   digitalWrite(ledPin, LOW);    // turn LED off
   

 if(buttonState == LOW && previous == LOW && millis() - time > debounce){       // check if the pushbutton is pressed

//   digitalWrite(ledPin, HIGH);    // turn LED on{
    if(stateLED == HIGH){
      stateLED = LOW; 
         mySerial.println("dark");   //print text
         mySerial.println("dark");   //print text
         mySerial.println("GOODNIGHT...");   //print text
         mySerial.println("dark");   //print text
         mySerial.println("dark");   //print text
   
    } else {
       stateLED = HIGH;    
         mySerial.println("light");   //print text
         mySerial.println("light");   //print text
         mySerial.println("=) MORNING!");   //print text
         mySerial.println("light");   //print text
         mySerial.println("light");   //print text
    }
    time = millis();
  }
  digitalWrite(7, stateLED);
  previous == buttonState;
}
//   } 
//    
//   digitalWrite(ledPin, HIGH);    // turn LED on
//   
////  buttonState = digitalRead(3);
////  if(buttonState == HIGH){       // check if the pushbutton is pressed
//// // else {
////   mySerial.println("dark");   //print text
////   mySerial.println("dark");   //print text
////   mySerial.println("GOODNIGHT...");   //print text
////   mySerial.println("dark");   //print text
////   mySerial.println("dark");   //print text
////   digitalWrite(ledPin, LOW);    // turn LED off
////   }
////   
////   digitalWrite(ledPin, LOW);    // turn LED off
//}